New 2000 5.7L Vortec $1500.00 (block#10243880 head 12558062)
Here is some info on the heads:
Cast iron, The eight-bolt intake bolt pattern is totally
different than the early model V8 12-bolt design.
2.02" intake and 1.60" exhaust.
This head with the big valves flow better then the
Phase 2 bowtie heads.Chamber volumes are 64cc and intake port
volumes are 170cc. The Vortec heads have raised intake ports and
"fast burn" chambers. The heads require the use of narrow
body"self-aligning" rocker arms and center bolt valve covers.
They will bolt to any Gen.1 block.
The correct Vortec intake manifold bolts are found under
PN-12550027. Use Vortec intake gasket PN-12529094.
Edelbrock has aluminum two and four barrel "Vortec" style intakes
that have the correct bolt hole positions. Edelbrock PN-7116
2000 Vortec 5.7 230HP $1500.00
1984 700R4 racing rebuilt $ 900.00
Mallory Unilite Dist(used) $ 130.00 (piece of trash. see below)
Starter and misc brackets $ 272.74
Flex Plate ATP Z 166 $ 79.90
Water Pump GMB 130-1350short$ 61.40
JTR conversion book. $ 41.75 (shipping included)
3 cans yellow gloss paint $ 9.00
2 cans brown primer $ 6.00
Edlebrock intake manifold $ 183.95 pt#EDE7116
ARP intake bolt set $ 20.95 ARP434-2101
Hooker BL/Hugger headers $ 129.95 HOO2100
Chrome oil stick assy $ 7.23 SPC 4255
Chrome Trans stick assy $ 18.15 SPC 5472
Chrome timing tab for SBC $ 2.91 SPC 4263
Tail house extention 700R4* $ 198.03 GM# 8673406
Extention shit rod 700R4 $ 17.27 GM# 24210711/24214689New #
Trans Mount 700R4 $ 25.25 GM# 475940
Motor Mounts (2 each) $ 99.00 GM# 3990332
Chrome dist hold down $ 4.97 SPC 4229
Chrome water outlet $ 13.13 SPC 4231
Holley pwr vlv saver $ 7.27 SPC 2408
Carb Stud Kit $ 4.98 SPC 4252
Ret Spring Bracket $ 7.08 SPC 4708
Lock Tight $ 7.72 PTX 64000
MCK carb dip 1 gallon $ 18.50 MCK 242
Carb gasket kit $ 5.25 SPC 680
More misc bolts+washers $ 28.95
JTR brackets...... $ 225.00 DAT-101-106+110
Temp Sender (240Z) $ 14.35
Holly fuel line $ 21.95 SPC-5952
15LB liq filled f/pressure $ 17.95
Oil spinner assy/filter $ 18.57 GM#3952301
Steel plates for trans br. $ 9.99
Steel for camber support $ 5.79
Drive Shaft $ 282.56 From Cannon Engineering
Holley fuel line $ 21.95 SPC 5952
Mallory ballest resistor $ 12.99 CSI 700
1 wire alternator $ 45.05 FAE 7127U3
Chrome water pump pulley $ 50.77 MRG 4970
Chrome crank pulley $ 51.98 MRG 4972
Fuseable link for alt. $ 2.19 GM-#14
Rad hose upper? $ 10.40 GATES 20573
Rad hose lower? $ 13.03 GATES 21324
Alt/fan/crank belt $ 10.19 GATES 7485
6' hydr 3/8" hose for trans $ 15.22
Spal fans 14" + 10" $ 363.00 From Scotts Fans Valencia Ca
CSI HEI dist $ 189.95 #66941
CSI HEI dist ends $ 4.50
Exhaust $ 495.00 2 into 1 3"- to 2stage flowmaster.
Throttle cable parts $ 8.00
Holley 600DP $ 279.00 #4776-5
1 hr Dyno time $ 100.00 SWAT performance in Palmdale
RearDisc $400.00 ish Modern-MotorSport
Brake Lines for rear $ 32.04 CNS BH177695
Braded rear lines $ 60.00 Modern-Motor Sports
R200 Rear 3.90 open $100.00
2 15X3.5" Centerline rims $100.00
Misc bolts ect $ 7.16
Centerline rims $300.00 15X8 rear 15X3.5 front
CoilOvers from Ross $500.00
TOTAL ----------
$7650.22 (OUCH)
About another $ 540 for tax!
===========================================
TOTAL $8190.22 so far....
============================================
Don't tell my wife!!!!!!
Total time so far 63 hrs total for conversion.
=============================================================
With the trans Tail housing, the dealer said that a new company
is making the part and it's 5 times as much.
Quality is very good though.
Copyright © 2002 NitroPhotos
All rights reserved.